-
JINHUA HUAMAO COMMODITY TRADE CO., LTD.
ADD: #11 Floor Of Narada Hotel, Shuangxi West Road #369, Jinhua City, Zhejiang Province.
Website: www.tigercraft.net
-
XIAOSHUN FACTORY - ZHEJIANG HUAFENG ELECTRIC TOOLS
ADD: Xiaoshun Town, Jinhua City, Zhejiang Province
-
FUCUN FACTORY - ZHEJIANG HUAFENG ELECTRIC TOOLS
ADD: Huafeng Road #2111, Jindong Economic Development Zone, Jinhua City, Zhejiang Province.
Website:
-
What should be paid attention to when using electric drill
1) The diameter of the drill used cannot exceed the allowable value of the electric drill.
2) The drill bit must be clamped with a key, and other tools are not allowed to hit the drill chuck.
3) Do not use too much force when drilling to prevent motor overload. If the speed is found to be reduced, the power supply should be cut off immediately for inspection.
4) The sporadic processed parts must be firmly on the fixture.
5) Do not wear gloves.
-
Safety operation rules for electric tools
1. The single-phase power cord of mobile electric ideas and hand-held power tools must use three-core soft rubber cable, and the three-phase power cord must use four-core rubber cable; when wiring, the cable sheath should go into the junction box of the device And be fixed.
2. Check the following items before using electric tools:
(1) There is no crack or damage to the shell and handle;
(2) The protective grounding wire or the neutral wire is connected accurately and firmly;
(3) The cable or cord is in good condition;
(4) The plug is intact;
(5) The switch action is normal, flexible and without defects;
(6) The electrical protection device is intact;
(7) The mechanical protection device is intact;
(8) Flexible rolling department.
3. The insulation resistance of electric tools should be measured with a 500V megohmmeter on schedule. If the insulation resistance between the live parts and the shell does not reach 2MΩ, it must be repaired.
4. After the electrical department of the power tool is repaired, it is necessary to conduct insulation resistance measurement and insulation withstand voltage test. The test voltage is 380V and the test time is 1 minute.
5. Separate switches or sockets should be installed for the electrical circuits connecting electrical ideas, appliances and tools, and a leakage current activity protector should be installed. The metal shell should be grounded; it is strictly forbidden to connect multiple devices with one switch.
6. The rated leakage current of the current leakage protector shall not be greater than 30mA, and the action time shall not exceed 0.1 second; the rated leakage operating voltage of the voltage type leakage protector shall not exceed 36V.
7. The control switch of the electric idea device should be placed within the reach of the operator. When a break, work or a sudden power outage occurs during work, the power-side switch should be blocked.
8. When using portable or mobile power tools, you must wear insulating gloves or stand on insulating mats; when moving tools, do not carry wires or rolling parts of tools.
9. When using Class III insulated power tools on wet or acid-containing sites and in metal containers, reliable insulation measures must be taken and special personnel must be placed for supervision. The switch of the power tool should be located within the reach of the guardian.
10. The disk plane of the magnetic chuck electric drill should be flat, clean, and rust-free. When performing side drilling or overhead drilling, measures should be taken to prevent the drill body from falling after power failure.
11. When using an electric wrench, the reaction torque fulcrum should be firmly secured and the nut can be tightened before it can be started.
-
How the power tool industry quickly occupy the commanding heights of the market
Forced by the decline of the foreign trade market, many hardware and power tool manufacturers and distributors have begun to change their strategies and began to focus on the development and innovation of the domestic hardware and power tool market. Some power tool companies and merchants that dominate domestic sales themselves , It is also taking advantage of its own advantages, actively making hard work on upgrading and upgrading, and its development is also quite rapid.
Although the domestic market capacity is not as large as the international market, the demand is still large. Most of them are professional electric tools. The sales price is relatively high, so the economic benefits are better. As long as the product quality is emphasized, the market share is continuously consolidated and expanded The future can also survive and develop. As the domestic power tool market is more picky about the quality and brand of power tools, both power tool dealers and direct users attach great importance to the quality and brand of power tools. Therefore, the market is increasingly inclined towards good quality, good brand power tools. As long as companies and sellers read the market well, electric tools will not be sold.
Domestic users have higher and higher requirements for the quality of power tools, and they are especially concerned about product efficiency, weight, life and other indicators. According to Jiuzheng Building Materials Network, taking the construction industry as an example, the quality problems of domestic electric tools are mainly reflected as: electric hammers are easy to heat, continuous working time is short, electric hammers have small impact and large vibrations, and the operator has to press hard. Deeper, the drill bit is easy to wear and break.
In order to better explore the domestic and foreign markets, more and more power tool manufacturers and distributors pay more attention to technological innovation, win with quality, and consolidate and expand the market with new products. Therefore, the brand awareness and brand effect of the power tool market are more obvious. Many power tool distributors with a little strength and scale have shown high enthusiasm for the distribution of good brand power tools.
The power tool market is maturing. Good brands will grow healthier and faster in a regulated and orderly competitive environment.
As manufacturers continue to attach importance to corporate brand building, increase investment in technology, and develop new products, the power tool industry has realized the transformation from a single small power tool product to a diversified, large-scale, modern, large-scale, and innovative power tool. The development of series products quickly occupied the commanding heights of the market
-
What should be paid attention to when using power tools
1. Before using the tool, a full-time electrician should check whether the wiring is correct to prevent accidents caused by the wrong connection of the neutral line and the phase line.
2. Before using the tools that have been left unused or damp for a long time, an electrician should measure whether the insulation resistance meets the requirements.
3. The flexible cable or cord that comes with the tool must not be connected long. When the power source is far away from the work site, a mobile electric box should be used to solve it.
4. The original plug of the tool must not be removed or changed at will, and it is strictly forbidden to directly insert the wire of the wire into the socket without a plug.
5. If the tool shell is found to be broken, the handle should be stopped and replaced.
6. Non-full-time personnel shall not disassemble and repair tools without authorization.
7. The rotating parts of the tool should have protective devices.
8. Operators wear insulating protective equipment as required.
9. A leakage protector must be installed at the power source.
-
J1G-ZP4-185
Voltage/Frequency: 220-240V,50Hz Input Power: 1400W Blade Dia: 210x2.5x30mm x 24T No-load Speed: 5000rpm G.W./N.W.: 12/9.5kgs Packing Size: 650x450x380mm/pc 20'FCL: 210pcs 40'GP: 420pcs 40'HQ: 500pcs Cutting Capacity Miter x Bevel Width x Height(mm) 0° x 0° 200 x 60 45° x 0° 152 x 60 0° x 45° 200 x 30 45° x 45° 152 x 35 -
J1G-ZP12-210
Voltage/Frequency: 220-240V,50Hz Input Power: 1500W Blade Dia: 210mm - 24T No-load Speed: 5000rpm G.W./N.W.: 12/10.5kgs Packing Size: 650x450x380mm/pc 20'FCL: 210pcs 40'GP: 420pcs 40'HQ: 500pcs Cutting Capacity Miter x Bevel Width x Height(mm) 0° x 0° 220 x 70 45° x 0° 155 x 70 0° x 45° 220 x 35 45° x 45° 155x 35 -
J1G-ZP33-255
Voltage/Frequency: 220-240V,50Hz Input Power: 1800W Blade Dia: 255mm-40T No-load Speed: 5000rpm G.W./N.W.: 19.5/16kgs Packing Size: 890x550x400mm/pc 20'FCL/40'FCL/40'HQ: 120/260/320pcs Cutting Capacity Miter x Bevel Width x Height(mm) 0° x 0° 305 x 90 45°x 0° 215 x 90 0° x 45° 305 x 38 45°x 45° 215 x 38 -
J1G-ZP32-255
Voltage/Frequency: 220-240V,50Hz Input Power: 1800W Blade Dia: 255mm-40T No-load Speed: 5000rpm G.W./N.W.: 12.5/10kgs Packing Size: 560x450x385mm/pc 20'FCL/40'HQ: 300/630pcs Cutting Capacity Miter x Bevel Width x Height(mm) 0° x 0° 140 x 70 45°x 0° 95 x 70 0° x 45° 140 x 38 45°x 45° 95 x 38 -
J1G-ZP12-K210AD
TECHNICAL SPECIFICATIONS Voltage/Frequency:
220-240V,50/60Hz Input Power: 1500W Blade Dia: 210mm-24T No-Load Speed: 5000rpm Packing Size: 610x520x330mm/pc 20'FCL:
315pcs 40'GP: 570pcs 40'HQ: 652pcs CUTTING CAPACITY Miter x Bevel: Width x Height(mm) 0° x 0° 305 x 70 45° x 0° 215 x 70 0° x 45° 305 x 40 left,305 x 20 right 45° x 45° 215 x 40 -
J1G-ZP35-K255
TECHNICAL SPECIFICATIONS Voltage/Frequency:
220-240V,50/60Hz Input Power: 2000W Blade Dia: 255mm-40T No-Load Speed: 5000rpm Packing Size: 650x450x380mm/pc 20'FCL:
270pcs 4O'GP: 450pcs 40'HQ: 540pcs CUTTING CAPACITY Miter x Bevel: Width x Height(mm) 0° x 0° 305 x 90 45° x 0° 215 x 90 0° x 45° 305 x 40 45° x 45° 215 x 40 -
J1G-ZP33-K255D
TECHNICAL SPECIFICATIONS Voltage/Frequency:
220-240V,50/60Hz Input Power: 2000W Blade Dia: 255mm-40T No-Load Spaeed: 5000rpm Pcking Size: 650x575x350mm/pc 20'FCL:
192pcs 40'GP: 432pcs 40'HQ: 504pcs CUTTING CAPACITY Miter X Bevel Width X Height(mm) 0° X 0° 305 X 90 45° X 0° 215 X 90 0° X 45° 305 X 40 left, 305 X2 5 right 45° X 45° 215 X 40 -
J1G-ZP2-190
Voltage/Frequency: 110-240V,50/60Hz Input Power: 900W/7.5A Blade Dia: 190mm No-load Speed: 5500rpm G.W./N.W.: 6.5/5.5kgs Packing Size: 480x315x285mm/pc 20'FCL/40'GP: 664/1330pcs Cutting Capacity Miter x Bevel Width x Height(mm) 0° x0° 110 x 50 45° x0° 75 x 50 0° x45° 110 x 25 45° x45° 75 x 25 -
J1G-ZP9-210
Voltage/Frequency: 110-240V,50/60Hz Input Power: 900W &1100W/7.5A & 9A Blade Dia: 210mm No-load Speed: 5500rpm G.W./N.W.: 6.5/6kgs Packing Size: 480x315x285mm/pc 20'FCL/40'GP: 664/1330pcs Cutting Capacity Miter x Bevel Width x Height(mm) 0° x 0° 120 x 60 45° x 0° 80 x 60 0° x 45° 120 x 30 45° x 45° 80 x 30 -
J1G-ZP-185
Voltage/Frequency: 110-240V,50/60Hz Input Power: 1500W/9.5A Blade Dia: 185/190mm No-load Speed: 5000rpm G.W./N.W.: 12/9.5kgs Packing Size: 650x450x380mm/pc 20'FCL/40'GP/40'HQ: 258/526/612 pcs Cutting Capacity Miter x Bevel Width x Height(mm) 0° x 0° 210 x 60 45°x 0° 145 x 60 0° x 45° 210 x 38 45°x 45° 145 x 38 -
J1G-ZP8-210
Voltage/Frequency: 110-240V,50/60Hz Input Power: 1500W/9.5A Blade Dia: 210mm No-load Speed: 110-120V:5000rpm, 220-240V: 4500rpm G.W./N.W.: 12/10.5kgs Packing Size: 650x450x380mm/pc 20'FCL: 258pcs 40'GP: 526pcs 40'HQ: 612pcs Cutting Capacity Miter x Bevel Width x Height(mm) 0° x 0° 220 x 70 45°x 0° 155 x 70 0° x 45° 220 x 35 45°x 45° 155 x 35 -
J1G-ZP8-210A
Voltage/Frequency: 110-240V,50/60Hz Input Power: 1500W/9.5A Blade Dia: 210mm No-load Speed: 110-120V:5000rpm,220-240V:4500rpm G.W./N.W.: 12.5/11kgs Packing Size: 650x450x380mm/pc 20'FCL: 258pcs 40'GP: 526pcs 40'HQ: 612pcs Cutting Capacity Miter x Bevel Width x Height(mm) 0° x 0° 305 x 70 45°x 0° 210 x 70 0° x 45° 305 x 35 45°x 45° 210 x 35 -
J1G-ZP27-255
Voltage/Frequency: 110-240V,50/60Hz Input Power: 1800W/15A Blade Dia: 255mm No-load Speed: 5000rpm G.W./N.W.: 12/9.8kgs Packing Size: 560x450x385mm/pc 20'FCL: 312pcs 40'GP: 620pcs Cutting Capacity Miter x Bevel Width x Height(mm) 0° x 0° 140 x 70 45°x 0° 95 x 70 0° x 45° 140 x 38 45°x 45° 95 x 38 -
J1G-ZP28-255
Voltage/Frequency: 110-240V,50/60Hz Input Power: 1800W & 2000W/15A Blade Dia: 255mm No-load Speed: 5000rpm G.W./N.W.: 19.5/16kgs Packing Size: 885x550x430mm/pc 20'FCL/40'GP/40'HQ: 120/250/300pcs Cutting Capacity Miter x Bevel Width x Height(mm) 0° x 0° 315 x 90 45°x 0° 215 x 90 0° x 45° 315 x 38 45°x 45° 215 x 38 -
J1G-ZP29-255
Voltage/Frequency: 110V-240V,50/60Hz Input Power: 1800W & 2000W/15A Blade Dia: 255mm No-load Speed: 5000rpm G.W./N.W.: 20.5/17kgs Packing Size: 885x550x430mm/pc 20'FCL/40'GP/40'HQ: 120/250/300pcs Cutting Capacity Miter x Bevel Width x Height(mm) 0° x 0° 315 x 90 45°x 0° 215 x 90 0° x 45°L 315 x 40 45°x 45°L 215 x 40 0° x 45°R 315 x 38 45°x 45°R 215 x 38 -
J1G-ZP20-255
Voltage/Frequency: 110V-240V,50/60Hz Input Power: 1800W/15A Blade Dia: 255mm No-load Speed: 5000rpm G.W./N.W.: 25/21kgs Packing Size: 95x59x41.5cm/pc 40'HQ: 258pcs Cutting Capacity Miter x Bevel Width x Height(mm) 0° x 0° 305 x 87 45°x 0° 215 x 87 0° x 45°L 305 x 50 45°x 45°L 215 x 50 0° x 45°R 305 x 25 45°x 45°R 215 x 25 -
J1G-ZP15-255
-
J1G-ZP4-305
Voltage/Frequency: 110V-240V,50/60Hz Input Power: 1800W/15A Blade Dia: 305mm No-load Speed: 5500rpm G.W./N.W.: 26/22kgs Packing Size: 95x59.5x49cm/pc 40'HQ: 220pcs Cutting Capacity Miter x Bevel Width x Height(mm) 0° x 0° 315 x 109 45°x 0° 220 x 109 0° x 45°L 315 x 66 45°x 45°L 220 x 66 0° x 45°R 315 x 39 45°x 45°R 220 x 39 -
J1G-ZP16-255
Voltage/Frequency: 110V-240V, 50/60Hz Input Power: 2000W/15A Blade Dia: 255mm No-Ioad speed: 110-120V: 5000rpm,220-240V: 5500rpm G.W/N.W: 25/21kgs Packing Size: 91×56×37.5cm 40'HQ: 360pcs -
J1G-ZP7-305
Voltage/Frequency: 110V-240V, 50/60Hz Input Power: 2000W/15A Blade Dia: 305mm No-Ioad speed: 110-120V: 3600rpm,220-240V:4500rpm G.W/N.W: 26/20.5kgs Packing Size: 910×575×530mm 40'HQ: 257pcs -
J1G-ZP12-255B
TECHNICAL SPECIFICATIONS Voltage/Frequency: 110V-240V,50/60Hz Input Power: 1800W Blade Dia: 255mm No-load Speed: 5500rpm G.W./N.W.: 16/12.5kgs Packing Size: 61x48.5x44cm/pc 20'FCL: 200pcs CUTTING CAPACITY Miter x Bevel Width x Height(mm) 0° x 0° 185 x 60 45°x 0° 135 x 60 0° x 45° 185 x 55 45°x 45° 135 x 55 -
J1G-ZP10-305B
Voltage/Frequency: 110V-240V,50/60Hz Input Power: 1400W Blade Dia: 305mm No-load Speed: 2800rpm G.W./N.W.: 24/20kgs Packing Size: 72x51.5x46.5cm/pc 20'FCL: 165pcs Cutting Capacity Miter x Bevel Width x Height(mm) 0° x 0° 185 x 60 45°x 0° 135 x 60 0° x 45° 185 x 55 45°x 45° 135 x 55 -
J1G-ZP30-255
Voltage/Frequency: 110V-240V,50/60Hz Input Power: 1800W/15A Blade Dia: 255mm No-load Speed: 5000rpm G.W./N.W.: 17.5/14kgs Packing Size: 79.5x48.5x40cm/pc 20'FCL/40'GP/40'HQ: 160/335/402pcs -
J1G-ZP12-255C
Voltage/Frequency: 110V-240V,50/60Hz Input Power: 1400W Blade Dia: 255mm No-load Speed: 2800rpm G.W./N.W.: 21/15.5kgs Packing Size: 61x48.5x44cm/pc 20′FCL: 200pcs Cutting Capacity Miter x Bevel Width x Height(mm) 0° x 0° 120 x 55 45°x 0° 90 x 55 0° x 45° 120 x 45 45°x 45° 90 x 45 -
J1G-ZP-305C
Voltage/Frequency: 110V-240V,50/60Hz Input Power: 1800W/15A Blade Dia: 305mm No-load Speed: 5000rpm G.W./N.W.: 24/20.5kgs Packing Size: 72x51.5x46.5cm/pcs 20'FCL: 165pcs Cutting Capacity Miter x Bevel Width x Height(mm) 0° x 0° 171 x 89 45°x 0° 121 x 89 0° x 45° 171 x 45 45°x 45° 121 x 45 -
J1G-ZP30-255A
Voltage/Frequency: 110V-240V,50/60Hz Input Power: 1800W/15A Blade Dia: 255mm, 24T No-load Speed: 2500rpm & 5000rpm G.W./N.W.: 17.5/14kgs Packing Size: 84x55x39cm/pc 20'FCL: 130pcs 40'GP: 275pcs 40'HQ 330pcs -
J1G-ZP-210C
Voltage / Frequency: 110V-240V, 50/60Hz Input Power: 1400W Blade Dia: 210mm No-load Speed: 5500rpm G.W./N.W.: 7.5/6.3kgs Packing Size: 47x 35.5x 32.5cm/1pc 20’FCL: 532pcs -
J1G-ZP-210D
Voltage / Frequency: 110V-240V, 50/60Hz Input Power: 1400W Blade Dia: 210mm No-load Speed: 5500r/min G.W./N.W.: 8/6.9kgs Carton Dimension: 47.5×36.5×33cm/1pc Pcs/Container (20’): 532pcs -
J1G-ZP5-210B
Voltage: 110V-240V, 50/60Hz Power: 1400W Blade Dia: 210mm No-Ioad speed: 5500r/min G.W/N.W: 15.5/12kgs Packing Size: 75×48×39.5cm/1pc Pcs/Container(20’): 180pcs -
J1G-ZP23-255
Voltage: 110V-240V, 50/60Hz Power: 1800W Blade Dia: 255mm No-Ioad speed: 5500r/min G.W/N.W: 16.5/13.5kgs Packing Size: 77.5×47.5×44.5cm/1pc Pcs/Container(20’): 165pcs -
DC
Voltage: 110V-240V, 50/60Hz Power: 1300W Blade Dia: ф210mm No-Ioad speed: 5500r/min G.W/N.W: 16.3/12.5kgs Packing Size: 75×48×39.5cm/1pc Pcs/Container(20’): 180pcs -
J1G-ZP18-255
Voltage: 110V-240V, 50/60Hz Power: 1800W Blade Dia: ф255mm No-Ioad speed: 4500r/min G.W/N.W: 26/21.5kgs Packing Size: 90×68×46.5cm/1pc Pcs/Container(20’): 100pcs -
J1G-ZP-210E
-
J1G-ZP9-305
Voltage: 110V-240V, 50/60Hz Power: 1800W Blade Dia: ф305mm No-Ioad speed: 4500r/min G.W/N.W: 27/23.5kgs Packing Size: 90×68×50.5cm/1pc Pcs/Container(20’): 80pcs -
J1G-ZP33-255
TECHNICAL SPECIFICATIONS Voltage/Frequency: 220V-240V,50Hz Input Power: 2000W Blade Dia: 255x2.5x30x40T No-load Speed: 5500 rpm G.W./N.W.: 19/16kgs Packing Size: 890x550x400cm/pc Pcs/Container: 120pcs/20′GP 260pcs/40′GP 120pcs/40′HQ CUTTING CAPACITY Miter x Bevel Width x Height(mm) 0° x 0° 305 x 90 45° x 0° 215 x 90 0° x 45° 305 x 38 45° x 45° 215 x 38 -
J1G-ZP33-K255
Voltage/Frequency: 220-240V, 50/60Hz Input Power: 2000W Blade Dia: 255mm-40T No-Ioad speed: 5000rpm Packing Size: 650x480x430mm/pc 20'FCL: 210pcs 40'GP: 420pcs 40'HQ: 504pcs Cutting Capacity Miter x Bevel Width x Height(mm) 0° x 0° 305 x 90 45°x 0° 215 x 90 0° x 45° 305 x 40 45°x 45° 215 x 40 -
J1G-ZP12-K210
Voltage/Frequency: 220-240V, 50/60Hz Input Power: 1500W Blade Dia: 210mm-24T No-Ioad speed: 5000rpm Packing Size: 565x435x360mm/pc 20'FCL: 288pcs 40'GP: 648pcs 40'HQ: 756pcs Cutting Capacity Miter x Bevel Width x Height(mm) 0° x 0° 220 x 70 45° x 0° 155 x 70 0° x 45° 220 x 40 45° x 45° 155 x 40 -
J1G-ZP12-K210D
Voltage/Frequency: 220-240V, 50/60Hz Input Power: 1500W Blade Dia: 210mm-24T No-Ioad speed: 5000rpm Packing Size: 610x520x330mm/pc 20'FCL: 315pcs 40'GP: 570pcs 40'HQ: 652pcs Cutting Capacity Miter x Bevel Width x Height(mm) 0° x 0° 305 x 70 45°x 0° 215 x 70 0° x 45°L 305 x 40 0° x 45°R 305 x 20 45°x 45° 215 x 40 -
J1G-ZP11-K305
Voltage/Frequency: 220-240V, 50/60Hz Input Power: 2000W Blade Dia: 305mm-40T No-Ioad speed: 5000rpm Packing Size: 750x650x375mm/pc 20'FCL: 162pcs 40'GP: 324pcs 40'HQ: 378pcs -
M1H-ZP3-185/210
Power Supply: 220-240V, 50Hz Rated Power: 1500W/11A Cutting Capacity: 70mm/90°,45mm/45° Weight: 15.5kgs Packing size: 64x59x32cm/pc Pcs/container: 252pcs/20'GP, 576pcs/40'HQ -
M1H-ZP2-250A / M1H-ZP2-250F
Power Supply : 220-240V,50Hz Power: 1800W No-load Speed: 5500rpm Blade Size: Φ250XΦ30X24T Cutting Range: 0°-45° Cutting Height: 0°Max.:85mm 45°Max.:60mm Dust Port: 35mm Operate Height: 829mm Table Size: 642 X 478 X 28mm Left Extension Table Size: 642 X 226 X 28mm Right Extension Table Size: 642 X 226 X 28mm Rear Extension Table Size: 78 X 220 X 28mm Packing Size: 70 X 57 X 33cm/pc 20'FCL: 224pcs 40'GP: 462pcs 40'HQ: 528pcs -
M1H-ZP5-250
Voltage/Frequency: 220-240V ,50Hz/60Hz Power: S1:1800W S6:25% 2000W No-load Speed: 5000rpm Table material: Steel Table Size: 563X583X28mm Max.cutting capacity on the left: 330mm PMax.cutting capacity on the right: 230mm Cutting Height Max: 85mm @0°, 65mm @45° Tilting Saw Blade: 0-45° Packing Size: 710X620X330mm 20'FCL/40'GP/40'HQ) 189/399/456pcs -
M1H-ZP3-254
Power Supply: 120V,60Hz Power: 1800W/15A No-load Speed: 5000rpm Table material: Steel Table Size: 563X583X28mm Max rip Cutting capacity: 230mm Cutting Height Max: 8mm @0°, 65mm @45° Tilting Saw Blade: 0-45° Packing Size: 710X620X330mm 20'FCL/40'GP/40'HQ: 189/399/456pcs -
M1H-ZP5-250A
Voltage/Frequency: 220-240V ,50Hz/60Hz Power: S1:1800W S6:25% 2000W No-load Speed: 5000rpm Table material: Steel Table Size: 563X583X28mm Max.cutting capacity on the left: 497mm Max.cutting capacity on the right: 396mm Cutting Height Max: 85mm @0°, 65mm @45° Tilting Saw Blade: 0-45° Packing Size: 710X620X330mm 20'FCL/40'GP/40'HQ: 189/399/456pcs -
M1H-ZP5-250B
Voltage/Frequency: 220-240V ,50Hz/60Hz Power: S1:1800W S6:25% 2000W No-load Speed: 5000rpm Table material: Steel Table Size: 563 X 583 X 28mm Max.cutting capacity on the left: 330mm Max.cutting capacity on the right: 230mm Cutting Height Max: 85mm @0°, 65mm @45° Tilting Saw Blade: 0-45° Packing Size: 710 X 620 X 330mm 20'FCL/40'GP/40'HQ) 189/399/456pcs -
M1H-ZP5-250C
Voltage/Frequency: 220-240V ,50Hz/60Hz Power: S1:1800W S6:25% 2000W No-load Speed: 5000rpm Table material: Steel Table Size: 563X583X28mm Max.cutting capacity on the left: 330mm PMax.cutting capacity on the right: 230mm Cutting Height Max: 85mm @0°, 65mm @45° Tilting Saw Blade: 0-45° Packing Size: 710 X 620 X 330mm 20'FCL/40'GP/40'HQ: 189/399/456pcs -
M1H-ZP5-250D
Voltage/Frequency: 220-240V,50Hz/60Hz Power: S1:1800W S6:25% 2000W No-load Speed: 5000rpm Table material: Aluminium Table Size: 650X576X28mm Max.cutting capacity on the left: 650mm Max.cutting capacity on the right: 338mm Cutting Height Max: 85mm @0° , 65mm @45° Tilting Saw Blade: 0-45° Packing Size: 780X700X355mm 20'FCL/40'GP/40'HQ) 138/294/343pcs -
M1H-ZP5-250E
Voltage/Frequency: 220-240V ,50Hz/60Hz Power: S1:1800W S6:25% 2000W No-load Speed: 5000rpm Table material: Aluminium Table Size: 650 X 576 X 28mm Max.cutting capacity on the left: 650mm PMax.cutting capacity on the right: 338mm Cutting Height Max: 85mm @0°, 60mm @45° Tilting Saw Blade: 0-45° Packing Size: 780 X 700 X 355mm 20'GP/40'GP/40'HQ: 138/294/343pcs -
M1H-ZP5-250F
Voltage/Frequency: 220-240V ,50Hz/60Hz Power: S1:1800W S6:25% 2000W No-load Speed: 5500rpm Table material: Aluminium Table Size: 640 X 530 X 40mm Max.cutting capacity on the left: 500mm Max.cutting capacity on the right: 700mm Cutting Height Max: 80mm @0° , 55mm @45° Tilting Saw Blade: 0-45° Packing Size: 910 X 750 X 370mm 40'GP/40'HQ: 233/270pcs -
M1H-ZP5-250G
Voltage/Frequency: 220-240V ,50Hz/60Hz Power: S1:1800W S6:25% 2000W No-load Speed: 5000rpm Table material: Aluminium Table Size: 640 X 530 X 40mm Max.cutting capacity on the left: 500mm Max.cutting capacity on the right: 700mm Cutting Height Max: 80mm @0°, 55mm @45° Tilting Saw Blade: 0-45° Packing Size: 910 X 750 X 370mm 40'GP/40'HQ: 233/270pcs -
M1H-ZP-255-1
TECHNICAL SPECIFICATIONS
Voltage/Frequency: 120V,60Hz Power: 1800W/15A No-load Speed: 5000 rpm Table material: Aluminum Table Size: 610 x 580 x 40mm Cutting Height Max: 89mm @0°, 63.5mm @45° Max rip cutting capacity:
24.5 inch Tilting Saw Blade: 0-45° Packing Size: 910 x 720 x 430mm 20'FCL/40'GP/40'HQ): 90/195/234pcs -
M1H-ZP3-254B
Voltage/Frequency: 120V,60Hz Power: 1800W/15A No-load Speed: 5500rpm Table material: Aluminium Table Size: 650 X 576 X 28mm Max.cutting capacity : 24.5 inch Cutting Height Max: 85mm @0°, 60mm @45° Tilting Saw Blade: 0-45° Packing Size: 780 X 700 X 355mm 20'FCL/40'GP/40'HQ: 138/294/343pcs -
M1H-ZP2-250E
Voltage/Frequency: 120-240V, 50/60Hz Power Supply: 1800W No-load Speed: 5000rpm Blade Size: ∅255X∅30X24T Table Size: 640x530mm Tbale Width Extension: 310x625mm Cutting Range: 0°-45° Height Adjustment: 0-80mm Cutting Height: 0°max.:80mm, 45°max.:55mm Packing Size: 91 X 75 X 37cm 20'FCL: 108pcs 40'GP: 228pcs 40'HQ: 270pcs Feature: Foldable and transportable leg Right and left sliding extension table -
M1H-ZP2-210
Power supply: 220-240V, 50Hz Rated power: 1500W/11A Cutting capacity: 70mm/90°,45mm/45° Weight: 15.5kgs Packing size: 64x59x32cm/pc 20'FCL/40'HQ: 252/576pcs -
M1H-ZP2-250 / M1H-ZP2-250D
Power Supply: 120V-240V,50/60Hz Power: 1800W No-load Speed: 5500 rpm Blade Size: ∅255X∅30mm X24T Cutting Range: 0°-45° Cutting Height: 0°max.:80mm 45°max: 63mm Dust Port: 35mm Operate Height: 829mm Table Size: 642 X 478 X 28mm Left Extension Table Size: 642 X 478 X 28mm Right Extension Table Size: 642 X 478 X 28mm Packing Size: 642 X 478 X 280mm 20'FCL: 224pcs 40'GP: 462pcs 40'HQ: 528pcs -
M1H-ZP5-255
Power supply: 220V-240V, 50/60Hz Cutting capacity: 88.9mm/90° , 63.5mm/45° Weight: 19.5Kgs Packing size: 73x64x37.5cm 20'FCL/40'GP: 162/324pcs -
M1H-ZP-255
Power Supply : 120V - 240V, 50/60Hz Input power : 1800W/15A No-load Speed : 4500 rpm Blade diameter : 10 inch(254mm) x 5/8” Table size : (L×W) 610×530mm G.W. /N.W.: 32/30kgs Packing Size : 110×76×45cm 40'HQ: 215pcs -
M1A-ZP-200
TECHNICAL SPECIFICATIONS Voltage/Frequency:
220-240V,50/60Hz Rated power: 250W, 1500rpm Table size: 300x300mm Tabel Material:
Steel Cutting Capacity height: 80mm/90° , 40mm/45° Cutting Capacity width: 200mm Blade size: 1400x6.5x0.35mm Unit height: 680mm N.W/G.W: 12/14kgs -
M1E-ZP-110
TECHNICAL SPECIFICATIONS Power Supply:
450W Cutting Wheel Diameter: 110mm Output Speed: 5200rpm Tabel Material: Plastic Blade Size: ∅110mmx 22.2mm Cutting Depth: 24mm@90°, 16mm@45° N.W./G.W.: 3.3/4.1kgs Packing Size: 27x20x18cm 20'FCL/40'HQ:
2720/5632psc -
J1G-ZP5-355
TECHNICAL SPECIFICATIONS Power:
110-240V,50/60Hz Blade Dia: 355mm No-Load Speed: 3600rpm G.W/N.W: 20/18.5kgs Packing Size: 60x35.5x44.5mm/pc Pcs/Container:
290pcs/20'GP3 CUTTING CAPACITY Bar(dia) 70x305 Pipe(dia) 70x215 Rectangle 40x305 left,20x305right Square 115x115mm Right Angle 135x135mm -
J1G-ZP5-355
TECHNICAL SPECIFICATIONS Voltage/Frequency: 110-240V,50/60Hz Power: 2400W Blade Dia: 355mm No-Load Speed: 3600r/min G.W./N.W. 20/18.5Kgs Packing Size: 60X35.5X44.5cm/pc Pcs/Container: 290pcs/20'Gp CUTTING CAPACITY Bar(dia): 51mm pipe(dia): 130mm Rectangle: 220X85mm Square: 115X115mm Right Angle: 135X135mm -
S1M-ZP-100
TECHNICAL SPECIFICATIONS Voltage
230V Frequency: 50Hz Input Power:
6000W /650W Grinding Disc Dia: Φ100mm/115mm No-load Speed: 12000r/min G.W./N.W.: 13/11.4kgs Carton Dimension: 43.5×32.5×26cm/6pcs Pcs/Container: 4800pcs/20'FCL -
S1M-ZP2-115
TECHNICAL SPECIFICATIONS Voltage
230V Frequency: 50Hz Input Power:
750W/800W Grinding Disc Dia: Φ125mm No-load Speed: 12000r/min G.W./N.W.: 14/13kgs Carton Dimension: 43.5×32.5×26cm/6pcs Pcs/Container: 4800pcs/20'FCL -
S1M-ZP4-125
TECHNICAL SPECIFICATIONS Voltage
230V Frequency: 50Hz Input Power:
750W /800W Grinding Disc Dia: Φ125mm No-load Speed: 12000r/min G.W./N.W.: 16.8/15.6kgs
Carton Dimension: 43.5×32.5×25cm/6pcs Pcs/Container: 4800pcs/20'ft -
S1M-ZP13-115
TECHNICAL SPECIFICATIONS Voltage
230V Frequency: 50Hz Input Power:
750W /800W Grinding Disc Dia: Φ115mm/125mm No-load Speed: 12000r/min G.W./N.W.: 14/13kgs
Carton Dimension: 43.5×32.5×25cm/6pcs Pcs/Container: 4800pcs/20'ft -
S1M-ZP33-230
TECHNICAL SPECIFICATIONS Voltage
230V Frequency: 50Hz Input Power:
2100W Grinding Disc Dia: Φ230mm No-load Speed: 6500r/min G.W./N.W.: 11.0/10.2kgs Carton Dimension: 55×29.5×17cm/2pcs Pcs/Container: 2000pcs/20'ft -
S1M-ZP80-100
Voltage/Frequency: 110V-240V,50/60Hz Input Power: 820W/7A Grinding Disc Dia: Φ100/115/125mm No-load Speed: 12000r/min G.W./N.W.: 15/14.4kgs Carton Dimension: 40.5x33.5x26cm/6pcs Pcs/Container(20′): 4800pcs -
S1M-ZP93-100
TECHNICAL SPECIFICATIONS Voltage
110V~240V Frequency: 50Hz/60Hz Input Power:
6000W /5A Grinding Disc Dia: Φ100mm No-load Speed: 12000r/min G.W./N.W.: 13/12kgs Carton Dimension: 50×33×25cm/8pcs Pcs/Container: 5200pcs/20'ft -
S1M-ZP94-125
TECHNICAL SPECIFICATIONS Voltage
110V~240V Frequency: 50Hz/60Hz Input Power:
6000W /5A Grinding Disc Dia: 1010/7.5mm No-load Speed: 12000r/min G.W./N.W.: 13.2/12kgs Carton Dimension: 40.5×32×26cm/6pcs Pcs/Container: 4800pcs/20'ft -
S1M-ZP69-115
TECHNICAL SPECIFICATIONS Voltage
110V~240V Frequency: 50Hz/60Hz Input Power:
600W /5A Grinding Disc Dia: Φ100mm/115mm No-load Speed: 12000r/min G.W./N.W.: 13.5/12.5kgs Carton Dimension: 41.5×31×25cm/6pcs Pcs/Container: 5200pcs/20'ft -
S1M-ZP51-115
TECHNICAL SPECIFICATIONS Voltage
110V~240V Frequency: 50Hz/60Hz Input Power:
620W /5A Grinding Disc Dia: Φ115mm No-load Speed: 12000r/min G.W./N.W.: 13.2/12.6gs
Carton Dimension: 40.5×31×26cm/6pcs Pcs/Container: 4800pcs/20'ft -
S1M-ZP-100,115,125
-
ZP29-230
-
S1M-ZP-84-115
-
ZP82-125
-
S1M-ZP83-115
-
S1M-ZP82-125B
-
S1M-ZP82-115
-
S1M-ZP81
-
S1M-ZP54-115
-
S1M-ZP53-100
-
S1M-ZP46-115
-
S1M-ZP35-115
-
S1M-ZP34-115
-
S1M-ZP33-100
-
S1M-ZP32-115
-
S1M-ZP29-230
-
S1M-ZP20-180
-
S1M--ZP20-115
-
S1M-ZP16-180
-
S1M-ZP16-125B
-
S1M-ZP16-115
-
S1M-ZP15-180